wraping. . KEEN new. Morbid. wraping KEEN new Morbid
Upload
Login or register
Hide Comments
Leave a comment Refresh Comments (29)
[ 29 comments ]
> hey anon, wanna give your opinion?
asd
#1 - doujinshi
Reply +103 123456789123345869
(01/13/2014) [-]
Morbid.
#11 to #1 - anon id: 80ed3e9d
Reply 0 123456789123345869
(01/14/2014) [-]
what does this have to do with this post anyway?
User avatar #19 to #1 - frutus
Reply 0 123456789123345869
(01/14/2014) [-]
>logitech
User avatar #20 to #1 - butterduck
Reply 0 123456789123345869
(01/14/2014) [-]
I would take the time to open the beanie gift rather then this weird plastic ****.
User avatar #21 to #1 - baaltomekk
Reply 0 123456789123345869
(01/14/2014) [-]
Just use a carpet knife. Goes through this **** as easy as butter.
User avatar #26 to #21 - skeptical
Reply 0 123456789123345869
(01/14/2014) [-]
*bone scissors
#13 to #1 - alstorp
Reply +1 123456789123345869
(01/14/2014) [-]
>Easy open
>Easy open
User avatar #6 to #1 - alphagex
Reply +2 123456789123345869
(01/14/2014) [-]
Flaged for the pain....

the pain that me and others had to endure opening that ****
#12 to #1 - europe
Reply +4 123456789123345869
(01/14/2014) [-]
>wireless
User avatar #5 - topheavymonkeyy
Reply +91 123456789123345869
(01/14/2014) [-]
Step by step guild to getting that out.
1. open wrapping
2. rip open plastic bin-liner
3. hit ice with hammer until completely broken
4. use a very sharp knife to cut off duct-tape and paper (You will need this for later so keep it on your person)
5. hit the pressure point of the metal (exactly in the center so it bends and pulls off some of the welding) or use an industrial blowtorch to take it off.
6. Acquire gift
7. murder whoever did that to you with the knife used earlier.
User avatar #15 to #5 - klabautermann
Reply 0 123456789123345869
(01/14/2014) [-]
Why not blowtorch it all?
#27 to #5 - anon id: 6f4eaf1e
Reply 0 123456789123345869
(01/14/2014) [-]
i like my 4 1/2" angle grinder. would be through that in less than 30 seconds
User avatar #8 to #5 - randomwanker
Reply +2 123456789123345869
(01/14/2014) [-]
If a weld is done right it can be stronger than the rest of the metal itself
#10 to #8 - topheavymonkeyy
Reply +2 123456789123345869
(01/14/2014) [-]
Still ,**** the rules
Still ,**** the rules
#18 to #5 - lolollo
Reply +6 123456789123345869
(01/14/2014) [-]
Oh right, I'll just grab the industrial blowtorch I have in the garage...
User avatar #25 to #18 - fuzzysixx
Reply +1 123456789123345869
(01/14/2014) [-]
Use your angle grinder.
User avatar #28 to #18 - topheavymonkeyy
Reply 0 123456789123345869
(01/15/2014) [-]
I have on. Every man should be equipped with the most powerful of power tools, what is this world coming to when every man doesn't own his own oil drill?!
#9 - mongooseproxc
Reply +34 123456789123345869
(01/14/2014) [-]
mfw i reach the steel part
#22 - alphadolan
Reply +11 123456789123345869
(01/14/2014) [-]
You're gonna like daddy's gift
User avatar #24 - arkadia
Reply +5 123456789123345869
(01/14/2014) [-]
thats a lot of effort for a **** gift
User avatar #2 - charagrin
Reply +3 123456789123345869
(01/14/2014) [-]
So it is a present of burnt paper and fabric? Considering it is filled with a plastic fiber hat and paper, when he sealed it by welding, he burnt everything inside. We used to boil water for coffee by placing the pot on metal we were fabricating, heat travels pretty dang far. The pot would boil after a few minutes even if it was 6 feet from the part we were working on.
User avatar #3 to #2 - xtrmbragnrytz
Reply 0 123456789123345869
(01/14/2014) [-]
It was mig welding, the hat would be fine
User avatar #4 to #2 - Lambda
Reply 0 123456789123345869
(01/14/2014) [-]
He just tack welded it, look close at the welds on the bottom. Probably barely transferred any heat at all to the metal.
User avatar #23 - dubious
Reply +1 123456789123345869
(01/14/2014) [-]
honestly I don't even think it'd be worth it, if i knew what it was I'd probably throw it away
#14 - danielesq
Reply +1 123456789123345869
(01/14/2014) [-]
traditional Swedish gift wrapping
traditional Swedish gift wrapping
User avatar #16 - twofreegerbils
Reply 0 123456789123345869
(01/14/2014) [-]
Heat transfer. If that beanie is cotton then it's nothing but char now. If it was polyester then it's a puddle.
User avatar #17 to #16 - heartlessrobot
Reply 0 123456789123345869
(01/14/2014) [-]
Only if you welded it for 10 minutes straight. You tack the corners, then weld each side, giving it time to cool down.
User avatar #7 - kipleonard
Reply 0 123456789123345869
(01/14/2014) [-]
Why is this not in the morbid channel?
[ 29 comments ]
Leave a comment